Thanks for the additional information. I was able to determine that the full kit you want is the Lippert # LC333966 replacement landing gear set including the legs and drop feet, cross bar, and gear box. We also have the Lippert # LC333964, which is the same kit, plus the motor and switch. view full answer...
From the photos you attached, the bottom half replacement you need for your converter model 7355 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp # PD4655V. This will solve all of the sparking/melting issues you are having with the unit. view full answer...
Yes, the Replacement Lead Leg # LC119102 is the correct leg for your VMC900R Venture Landing Gear on your 2009 Keystone Cougar 5th wheel.
The Replacement Follow Leg # LC119101 is also available if you would like to replace the follow leg as well on your Cougar.
The Ultra-Fab Spring-Loaded Quick Pins # UF17-943031 are replacements for your current pins as the new legs only include a snapper pin. view full answer...
The # RVLG-8000 you were looking at would work well for replacement landing gear on your 2004 Keystone Laredo 29BH. The manual hand crank # RVLG-HDL is sold separately. You can also add a switch # LG-145236 and motor # LC142178 for a power option.
Another great option would be the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. The jacks each have a motor so they function independently. This means you can easily level your 5th wheel on uneven surfaces while you're camping or... view full answer...
According to our information you'll need the Replacement Lead Leg # LC119102 for your Venture VMC900L landing gear kit. If you end up needing the follow leg as well that can be found on our site as part # LC119101.
Attached is a review video for you to check out. view full answer...
It sounds like you have the Lippert Ground Control Electric Leveling System and in which case you will need the Replacement Lead Leg for Lippert Components Ground Control 3.0 Electric Leveling System part # LC305340 for the leg and motor or the Replacement Front Jack for Lippert Ground Control 3.0 Leveling System part # LC362485 for just the leg. These will both work on either side of the trailer, front left or front right. view full answer...
It sounds like the compressor is bad and you'll need to replace the unit. I recommend getting the Advent Air Replacement RV Air Conditioner for Dometic Setup w/ Start Capacitor - 15,000 Btu - White # ACDOM150. This will directly fit your current wiring for an easy swap with no changes required on the inside of the trailer. view full answer...
For your Venture ADTH landing gear the best replacement gear box would be the Stromberg part # LG-179015 that you referenced. This is the heavier duty aluminum replacement option that would last longer than other similar options. view full answer...
The Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear # LC276602 is the one you will need for your 2005 Keystone Sprinter 252RLS 5th wheel. It is a direct replacement for your damaged Venture gear box. view full answer...
For your 2011 Keystone Cougar 278rks, you will want the Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear # LG-179015. This will be a direct replacement for your landing gear and motor. view full answer...
The Replacement T-Handles for JT's Strong Arm Jack Stabilizer Kits - Qty 2 # LC314594. The outer sleeve you are seeking is Replacement Outer Stabilizer for JT's Strong Arm Jack Stabilizer - 1-1/4" OD - Qty 1 # LC191014. view full answer...
From online research, yes, as it looks like your 2005 Keystone Raptor 5th Wheel most likely has the Venture landing gear system. I highly recommend you verify this before ordering though. The Lippert Electric Landing Gear Set, # LC333964 has outer tube length of 29-1/2 inches and the distance between the weld stops is 17-1/2 inches. You can compare these dimensions to your current landing gear to see if this will install without the need for any modification. Otherwise, mounting brackets... view full answer...
The correct repair kits we have for the Venture Landing Gear Legs VMC900 is part # LC146060 for the follow leg and part # LC146059 for the lead leg. view full answer...
Yes, the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00 is the correct part for your 6504-414. This kit replaces the bow-tie bracket, motor, and blade for your Fan-Tastic Vent roof vent fan. Since the fan stopped working and is now out of production, you may also want to consider a total replacement.
If you decide to completely replace the fan I recommend the Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 14-1/4" x 14-1/4" # FV802250... view full answer...
It sounds like the axles on your 2006 Keystone Cougar 289EFS 5th wheel may have been modified from the original 4,400lb trailer brakes. The 4,400lb axles used parts that have been discontinued, but as you mentioned your brakes show T-52 on the backing plate you may be able to use the Dexter Electric Brake Kit # 23-105-106-09 which has both the standard 5 bolt pattern and 4 bolt ALKO mounting pattern. I have included images below with the measurements for both bolt patterns. If you have... view full answer...
We have repair kits for the VM900L series. The repair kit for the follower leg is # LG-146060 and the repair kit for the lead leg is # LC146059. Replacing the parts is going to be a whole lot less expensive that replacing the legs.
If you want to replace the legs anyway then we have # LG-179014 as the follower and # LG-179013 as the lead leg. view full answer...
The Lippert Replacement Reverse Polarity Solenoid for RV Hydraulic Slide-Outs part # LC136046 and part # LC118246 are the same solenoid but vary in how they mount. The part # LC136046 mounts using a strap around the motor like what you have therefore this is the correct replacement for you whereas the part # LC118246 mounts on a tray beside the motor. view full answer...
For the Stromberg Carlson Electric Landing Gear Set we have the Replacement Motor, # LG-142178 that is designed for use with Stromberg Carlson model LG-1 or LG-2. This has a weight capacity of 5,500 lbs. and a motor speed of 5,500 rpm's. The Replacement Motor, # LG-196308 is for use with Stromberg Carlson model LG-3 or LG-4 models and has a weight capacity of 6,500 lbs. and a motor speed of 5,430 rpm's.
Please compare these to the replacement motor you used for options of a larger capacity.... view full answer...
There are a few 2004 Keystone Laredo models available but I am pretty confident that yours has 3,500 lb axles which would mean that for the left hand side you'd want the part # AKEBRK-35L-SA and then for the right hand side part # AKEBRK-35R-SA which are self-adjusting.
If you have something different though let me know and I'll see if we can help. view full answer...
Currently the LED RV Security Light # CE76FR is the only 12 volt powered motion activated light that we have that would work for your 2020 Keystone Cougar 268MBI in your entry way.
While it does not have a switch you could add a Mini-12V Switch # 37212785 next to it or your existing light to allow you to switch it on and off. view full answer...